Free, no-pressure on-site estimates across all of Dallas County, family-owned & backed in writing. Free estimates · All of Dallas County Call (469) 265-6259 →
Patio Covers · Garland

Patio Covers in Garland, TX

Many postwar back yards end at a bare slab in full sun, and a roof tied into the house gives that slab shade you can actually sit under. Serving Garland and all of Dallas County.

Call (469) 265-6259

Get your free quote

Two quick steps. We call back within one business day.

Why Estrada

Making older back yards usable

Garland’s central neighborhoods are mostly postwar homes on older lots, and many back yards still have nothing between the slab and the afternoon sun. A cover tied into the house is the simplest way to make that space usable through a Texas summer.

On a low postwar ranch, the existing eave sets the limit for everything else. We measure eave height and roof slope first, because the cover has to drain at the city’s minimum pitch and still leave headroom at the back door. Sometimes that means lifting the ceiling with a gable instead of running a flat extension. Posts come next, placed by the setback, and the overhang is planned last so the shade line lands where you sit.

  • Eave height and slope measured on day one
  • Gable option when a flat tie-in sits too low
  • Shingles matched to your existing roof
  • Post layout drawn before the roof design
  • Insulated roof to cut heat off the slab
Vaulted cedar patio cover ceiling with a ceiling fan, stone fireplace, TV and outdoor kitchen beside a pool
Garland, TX
What we build

Patio cover options in Garland

Low-Slope Shingle Cover

A shingled extension that drains properly while meeting a low ranch eave.

Raised Gable Cover

Lifts the ceiling for headroom and air movement over a small slab.

Side Yard Cover

Shades a side patio or the walkway that runs along the house.

Insulated Solid Roof

Insulated panels that block afternoon sun on a slab with no shade at all.

Design first

Want to see it on your house first?

Some owners like to see the roof pitch and post spacing before they commit. We can model the cover against your house in 3D so you can try a different size or finish on screen.

Mention it when you book the measuring visit in Garland.

Ask about a 3D rendering
3D design rendering of a cedar pergola over a fire pit seating area beside a brick home
3D rendering

Before you build a patio cover in Garland

  • Garland requires a building permit for every patio or porch cover, whether it is attached to the house or freestanding in the yard.
  • A cover cannot sit in the required setbacks. Next to a street that is typically 20 feet and can be as much as 35 feet, and an attached cover typically stays 10 feet off the rear line and 6 feet off the side, measured from the posts. We confirm the numbers for your lot with Garland Building Inspection before we draw the plan.
  • The roof cannot be corrugated metal or plastic, a shingle roof needs at least a 2:12 pitch, and any metal patio cover has to be engineered.
  • A rear yard cover may have a roof overhang of 2 feet, and a side yard cover may have 3 feet.

Garland HOAs

Firewheel Estates, Fairways at Firewheel, Spring Park and the Valley Creek associations off Firewheel Parkway all have HOAs, and those boards typically review exterior additions like patio covers, while many older central streets have no association at all. Garland states that it enforces city ordinances only and that following deed or HOA restrictions is up to the homeowner. Either way, Estrada matches the roof pitch, shingle or metal finish and trim color to the house and prepares the plans for the HOA submission when one is needed.

Source: City of Garland Patio Cover permit page

Owner on every job
In-house crews, no subs
Permits handled
Written workmanship warranty

Common questions in Garland

Is a city permit required for my Garland patio cover?

It is. Garland draws no line between covers on the house and covers out in the yard, so both go through Building Inspection. Estrada prepares the drawings and handles the filing.

What happens first when I hire Estrada for a Garland patio cover?

We visit, measure the eave and the slab, and mark rough post spots in the yard. Then we confirm your lot’s numbers with the city, draw the cover and file the permit, which Garland wants for attached and freestanding covers alike. Building starts once the permit is approved.

My ranch roof is very low. Can a cover still fit?

Usually, yes. A cover attached at a low eave can end up with too little headroom once it has enough slope to drain. When that happens, we look at a gable or a tie-in higher on the roof. We sketch both options on site so you can compare headroom before anything is drawn.

Can I put metal roofing on my Garland cover?

Garland rules out corrugated panels, so it would have to be another kind. Most older homes here have shingles, and matching them is usually the cleanest look. If your house already has a metal roof, ask us. We confirm with the city what it will accept on a wood-framed cover before we draw it.

Ready when you are

Get your patio cover quote in Garland, free and no-pressure.

We walk your Garland yard, give you a straight price, and show you how the cover is built and tied in.